Cleaning and servicing your brake calipers is a crucial job if you've ridden through winter or had the bike laid up for a while, but it only takes an afternoon. So what are you waiting for? 

But where to start? Well, a brake caliper is the bit of equipment on your bike that contains the brake pads along with the hydraulic mechanism that presses the pads against the disc. That means there are several parts in there that move regularly with a reasonable amount of force. As a result, engineering tolerances are high and it's important you do this job in a structured fashion.

You don't need to be an engineer in order to service your brake calipers, though. It's easily achieved by an amateur mechanic at home. So if you're curious about how to unsieze a brake caliper, or how to open a brake caliper piston, this article can help. 

Dirty pad retaining pins and mucky pistons can cause binding as well as a harsh pull at the lever, so cleaning both keeps things slick. When doing this task, it’s best to work on one caliper at a time, as pushing out the pistons in both calipers could run the fluid reservoir dry. Remove the retaining pin before removing the caliper as they can seize in place, making removal difficult.

With the pin out, remove the pads and inspect them for condition. Take a note of which side of the caliper each pad comes from so they can be put back in the same position if they have plenty of life left in them. If they are worn then this is the time to source replacements. Check that they are the correct spec by laying them side by side with the originals to make sure they are identical.

Fill a bucket with warm water and add in a bit of bike cleaner. Moisten the caliper with water and then spray on some brake cleaner and allow it to dwell for a minute or so. The cleaner will penetrate and loosen dirt and contamination. Be accurate when spraying cleaner on the brake caliper, as you don’t want to be overspraying on to the brake discs and fork legs.

Using a suitable nylon brush, agitate the cleaner and pay attention to the areas that are within the caliper and between the pistons. It’s important to clean the pistons, so pump them out with the lever (not too far!) and scrub the sides. Also scrub the pad retaining pins and anti-rattle springs.

Use a hose to gently rinse away the dirt, or use a sponge with clean water to do the same thing. Rinse between the pistons and make sure that the inside of the pistons aren’t harbouring a mini reservoir of scuzz. It’s important that all of the cleaner is rinsed  off otherwise it can leave a white residue when dry.

If you have an airline, then use it to blow away most of the water. Use a drying towel that will absorb all remaining moisture and dry inside the caliper pistons. With the caliper dry, apply some red rubber grease to the pistons, then push them in and out a few times. You’re looking for minimal resistance, so that when you release the lever the pistons relax.

When fitting pads, you’ll need to gently push the pistons back. There are ‘winding back’ tools you can get for this specific job but if you are careful you can use a large flat tool to ease them back slowly. Try to avoid big screwdrivers, as you can damage the pad. A whole book could be written on copper grease but it’s rarely required on modern pads.

8. Refit and torque it up

With the pads fitted check that any retaining pins, clips or shims are installed as per the workshop manual. Refit the caliper and tighten up with a torque wrench. Check the tightness on any pad-retaining fasteners. Pump the front brake lever – initially it will feel soft but after a few pumps it should start to feel normal again. Check the brake fluid level in the reservoir is correct, top up if necessary with fresh fluid.

9. Give it a final clean

Using clean workshop paper towel, clean the brake disc with a dedicated brake cleaner. Most discs have two parts – the carrier in the middle and the brake disc surface itself. Clean the carrier first using brake cleaner and wipe it off with clean workshop paper  towel. Clean the outer disc last using fresh paper towel and brake cleaner. Use a rotating motion with the towel until the disc is wiped clean.

And that's it! Job done. You've now successfully serviced your stoppers. 

Read the latest stories causing a buzz this week in Advice…

Rising from the ashes: Top Mountain Motorcycle Museum re-opens

A motorcycle museum that was completely destroyed by fire in January 2021 – along with 330 rare... more >

How Mutt Motorcycles are taking on the big dogs with their small-capacity retros

British bike manufacturers are beginning to dominate the headlines once more in a modern reflection... more >

Going the distance: 120 years of Royal Enfield adventures

In the world of YouTube and Instagram and massive machines with satnavs, spotlights and metal... more >

Winter wonderland: 16 secrets of conquering even the coldest conditions

Riding all year round is one of the most life-enriching things you can do. Yes – some people will... more >

How to fit clip-on bars for that tucked-in race-style ride

If your bike has standard fitment one-piece handlebars and you want a tucked-in race-style riding... more >

MCN's Jordan Gibbons finds battery bikes are the perfect pal for city life

No matter how much some people might yearn for carbs, induction roar and the sweet smell of Castrol... more >

Datalogger, professionally testing bikes for over 25 years.

© 1955-2022 Bauer Media Group

Bauer Media Group consists of: Bauer Consumer Media Ltd, Company number: 01176085, Bauer Radio Ltd, Company Number: 1394141 Registered Office: Media House, Peterborough Business Park, Lynch Wood, Peterborough, PE2 6EA H Bauer Publishing, Company Number: LP003328 Registered Office: Academic House, 24-28 Oval Road, London, NW1 7DT. All registered in England and Wales. VAT no 918 5617 01 H Bauer Publishing are authorised and regulated for credit broking by the FCA (Ref No. 845898)